Circuit Board For Ac Unit

Share This Post

Can I Replace An Ac Motherboard Myself

AC Fried circuit board replacement fix HVAC Ammana

Replacing an AC motherboard is a simple DIY task. Be sure to order the correct circuit board and follow these instructions:

  • Confirm that replacing the circuit board yourself won’t void the AC warranty.
  • Turn off the power to the system.
  • Take a picture of the wiring to reference later on.
  • Ground your hands by dragging them across a metal surface to eliminate static electricity that could damage the new control board.
  • Remove the control board screws, leaving wires attached if possible. If not possible, transfer the wires one at a time to the new board.
  • Attach the new control board using the same screws.
  • Refer to the picture taken earlier to confirm that the board is wired the same as before.
  • Power on the system.
  • Identify Your Circuit Board

    There are scores of different Furnace, Air Handler and Heat Pump Boards. Some are called Fan Timers, others Control Boards, Defrost Controls, Defrost Timers, Circuit Boards, Logic Boards and probably as many other names again, depending on the equipment or board manufacturers terminology!

    We will TRY to make this as painless as possible with a couple of pictures below.

    The shot below is of a YORK Ignition Control Part # 331-01933-000.For use with the following YORK Furnaces using Hot Surface Ignition.


    The ball point pen is pointing to the Part # 331-01933-000. This is the number you are looking for on our web site when it pertains to these boards. MANY times the manufacturer will have superseded these numbers with a different number which REALLY confuses things for all of us. If you can’t find your number on our site this is probably why! Call us with the number you have on your existing board, the brand of the equipment as well as the Model and Serial number found on the equipment and we will call the manufacturer for you for pricing and availability.

    Here is a close up of the same board.

    Below is a circuit Board for an older Carrier Furnace which uses a standing pilot or Spark Ignition system .

    Are you confused now?

    electrical circuit board

    How Much Does It Cost To Replace A Circuit Board

    The cost of replacing an AC circuit board ranges from $125 to $625. However, the parts of an AC circuit board costs between $100 and $150. An AC circuit board can be bought online for $50 to $250. Replacing an air conditioner circuit board is a better option for the long run rather than getting it repaired multiple times. A professional from an AC repair in Los Angeles can replace your circuit board.

    Platinum Air Conditioning Inc. is an AC maintenance in Los Angeles. We specialize in air conditioner installations to improve indoor air quality and provide our customers with the best services. Get your AC tune-up in Los Angeles. Call us up at to find out all about our services. Get your repair scheduled now!

    Also Check: Best Heated Socks For Skiing

    How Long Does An Ac Circuit Board Last

    An AC circuit board lasts 15 years or more, typically as long as the HVAC system itself. The circuit or control board may fail earlier for several reasons:

    • A fuse that is dirty or not the correct size
    • Aging over time causes the control board to degrade
    • Clogged air filters result in an overheating blower motor
    • Damage from power surges
    • Loose wiring is caused by vibrations over time, which results in a short in the circuit board
    • Pests make a home inside the outdoor cabinet and short circuit the wiring

    How Much Does A Heater Control Board Cost

    95% new good working for inverter air conditioning unit board ...

    A furnace control board replacement costs$300 to $650 on average. The furnace control board operates the sequence of the heating cycle. If the control board detects a problem, it shuts the furnace down for safety.

    When hiring an AC repair service near you, be sure to:

    • Look for an HVAC contractor that has been in business for more than five years.
    • Browse their reviews on HomeGuide and Google.
    • Get at least three estimates to compare. Confirm the replacement components are comparable in the estimates.
    • Avoid selecting the lowest quote as quality may suffer.
    • Get a detailed estimate, contract, and warranty in writing before the work begins.
    • Never pay in full upfront. Follow a payment plan and do not make the final payment until fully satisfied.

    How Much Does It Cost To Replace Ac Circuit Boards

    The price to replace a failed PCB is going to depend on several different factors, including the year, brand, and model of your AC unit. Therefore, on a newer air conditioner model, it will cost around $500 . Since this is definitely not cheap, it can be beneficial to consider getting a used PCB, particularly for a newer AC model.

    The new PCB for the Mitsubishi Mxy-3a28va, for example, will cost you around $600. However, a second-hand model will only cost around $300. You can save $300 with this option.

    Why Replace A Pcb Rather Than Repair

    It is wise always to replace a faulty PCB rather than working to repair it. That is because the repairing process may take longer and demands the services of a skilled technician, which may end up being expensive for you. In fact, experts and technicians recommend repairs as the last result if all fails and if the ACs PCB in question was discontinued.

    Lets not forget the error aspect of repairs. In other words, when it comes to repairs, there is always a high probability of errors.

    What Is A Furnace Control Board

    The control board, also known as a furnace circuit board, is the mastermind of your furnace operation.

    Circuit boards regulate all the furnace components, including the gas valves, ignition, blower motor, and flame sensor.

    Symptoms of a failing furnace control board include illuminated warning lights on the furnace diagnostic system and difficulty regulating room temperature, even when the thermostat registers a consistent reading.

    A malfunctioning fan blower control or hot surface ignitor is more common than control board issues, though it creates similar problems.

    The 7 Most Common Causes Of Air Conditioning Breakdowns

    344 Communication in Inverter AC Outdoor Unit Circuit Board Repair Course – Part 4

    Air conditioner breakdowns are extremely frustrating to deal with as air conditioning systems are essential to any households comfort and wellbeing. Every air conditioner brand is subject to breakdowns and even though Daikin air conditioners are some of the best in Australia, breakdowns can still occur. That is why here at Logicool Air our expert Air Conditioning Service ensures that we promptly and professionally work to resolve any air conditioning breakdown. After working on air con units for over 15 years, we understand how to deal with the most common problems.

    The seven most common reasons why an air conditioner will breakdown are:

    • A Blown Fuse
    • Burnt Out Printed Circuit Board
    • Blocked Filters/Coil
    • Water Leaks

    Can A Pcb Be Repaired

    Fortunately, it is possible to repair a PCB. However, the task demands correctly diagnosing the problem, repairing tools, ad technical knowledge.

    However, specific circuits must be repaired within a workshop environment and cannot be fixed on-site. After repairs are completed, a test needs to be conducted to ensure the PCB is functioning correctly.

    What Causes Pcb Damages In An Ac

    PCB circuits are extremely sensitive to various elements and electrostatic discharge . It is important to note that even a small discharge of ESD can damage components on the PCB. Below are other common reasons why AC PCBs get damaged:

    • Incorrect input voltage in the AC PCB during installation by a technician
    • Short circuit. This is far the most common cause of PCB damages
    • Small insects like ants and cockroaches. It is common knowledge that insects like cockroaches love a warm place. As such, they often hid in electrical and electronic devices, which produce heat . For this reason, when a cockroach gets into the circuit board, it is most likely going to cause damage through short circuits, creating static charges, and others.
    • Exposure to the elements. The most common causes of damage to PCB is exposure to heat, moisture, and dust.
    • Accidental impact. This involves accidents like dropping it during AC cleaning
    • Age is another very common factor. Everything in this world has its age limit, and unfortunately, most PCB components have a limited age limit.

    What Is An Air Conditioner Pcb

    PCB is an abbreviation for the term Printed Circuit Board. The devices are similar to the CPU or Motherboard of a computer. It is important to realize that a Motherboard is still contained in an air conditioner.

    PCB is a green board that acts as the wiring for different components such as transistors, capacitors, resistors, etc. There are connections in between the various components called conductive tracks. They are made with a layer of copper and masked with a fibreglass silkscreen.

    A PCBs main function is designed to include different components to perform data communication, a specific command, or calculate the output for controlling the AC.

    Can Aircon Circuit Board Be Repaired

    Circuit Board  B1809911S Goodman/Janitrol Furnace Control Board ...

    The advancement in air conditioning technology has resulted in designs that enable superior energy saving ability and improved functioning of the air conditioner. Old technology utilises electrical components to perform direct control operation of motors and compressor. This results in unoptimized operation that leads to higher energy consumption.

    Recent technology introduces optimized control that enables the aircon to adjust operation accordingly to the required cooling load. This control allows lower energy consumption. The new technology uses printed circuit board to perform complex communication, data calculation and output operation.

    The circuit board and its components, like any other parts in the air conditioning system, are subject to lifespan exhaustion as well as damage. We shall briefly discuss the common breakdown scenarios:

  • An air conditioner circuit board operate in both voltage AC and DC voltages. Whenever there is a current surge, the circuitry may be damaged by sudden introduction of higher voltage that is beyond its operating range.
  • Inputting of incorrect voltage into aircon circuit board by an inexperienced technician during installation can also damage the board.
  • Damage or shorted field wiring is another cause of circuit board damage. Shorted or damage wire also results in incorrect or excessive introduction of voltage.
  • Brands

    Why Should A Pcb Be Replaced Instead Of Repaired

    It is always smart to replace a PCB that is faulty instead of trying to repair it. That is because the repair process might take longer and a skilled technicians services are required, which could end up being quite expensive for you. Technicians and experts, in fact, recommend repairs only if all else fails and as the last result or if the ACs PCB has been discontinued. Another thing to keep in mind is that repairs always have an error aspect to them. As a result, there is always a high possibility of errors when repairs are involved.

    What Should You Know About Your Hvac Control Board

    Most homeowners are familiar with afew critical parts of their furnace, such as the electric ignition or the airfilter. These crucial elements help your furnace to operate correctly andefficiently, but they are simple components that are incapable of regulatingthe operation of your home’s furnace on their own. Instead, they rely on thecontrol board to act as the brains of the unit.

    Although any modern furnace shouldinclude this element, many people may be unfamiliar with its function or thesigns of failure. Electronic components can be intimidating, but learning a bitabout your control board can help you understand when something has gone wrong.Keep reading to discover how this lone circuit board helps keep you warm andtoasty as summer transitions into fall and winter.

    Understanding the Many Roles of theControl Board

    Your control board serves severalpurposes in your furnace and air handler unit. One of its primary functions isto receive input from your thermostat and furnace sensors, make decisions basedon that data, and then distribute messages to other components in the system.Without a properly functioning control board, elements such as your igniter maynever receive instructions to turn on.

    Surprisingly, your control board iseven responsible for powering your home’s thermostats. A transformer insideyour furnace housing converts your home’s 120Vline voltage to 24V. This voltage then supplies thecontrol board, which distributes that power to each thermostat in your house.

    What Are Signs The Control Board Needs Replacing

    Common warning signs the control board needs replacing include:

    • Unstable room temperature, especially when the thermostat is working
    • Interruptions in the regular event sequence like the ignition not turning on or the blower running after everything else has stopped.
    • LED warning lights on the control board flashing an error code

    Perform A Transformer Power Test

    Bryant rooftop ac unit repair circuit board diagnosis

    As the name suggests, the function of the transformer is to transpose the power coming from the high voltage wires from 120 volts to 24 volts.

    Test the high voltage wires by touching the meter leads to each wire. Your meter should give a reading of 120 volts.

    Follow the same steps with the two low-voltage wires. Your meter should give a reading of 24 volts.

    If you dont get a 24-volt reading on the low voltage wires, it means that your transformer is not converting the voltage from 120 to 24 and is most likely the source of the problem.

    If you get an accurate reading from all the wires in the transformer, you know that the problem lies somewhere other than your transformer. Continue to the next step.

    What Is The Cost Of Replacing An Ac Circuit Board

    The cost of replacing a failed PCB will depend on many factors, such as the model, brand, and year of the AC unit. As such, for newer air conditioner models, it will cost you about $500 . Because clearly, this is not cheap, it would be favourable to consider a second-hand PCB as an option, especially for new AC models.

    For example, the new Mitsubishi Mxy-3a28va printed circuit board will make you cough up about $600. But if you choose the second-hand option, it will cost you about $300. With this option, you will be able to save $300.

    How To Wire An Air Conditioner For Control 5 Wires

    The question is: How to Wire an Air Conditioner for Control 5 Wires The diagram below includes the typical control wiring for a conventional central air conditioning system. Furthermore, it includes a thermostat, a condenser, and an air handler with a heat source. Moreover, the heat source for a basic ac system can include heat strips for electric heat or even a hot water coil inside the air handler that gets hot water from a water heater or boiler.

    Every conventional residential ac system uses 24 volts for the control of the system. All the relays in the system have 24-volt coils. Circuit boards or printed circuit boards found in modern systems utilize 24-volt control, which originates from the control transformer. Finally, typical systems that do not use 24-volt control are window unit air conditioners, ductless mini-split systems, and baseboard electric heating systems.

    What Causes Ac Circuit Board Failure

    The main reason behind premature circuit board failure is ESD or Electrostatic Discharge at the time of assembly. There are other reasons as well, like: 1. Exposure to intense heat. 2. Accumulation of dust over the contact and the circuit board itself. 3. A power surge or overload. 4. Excessive moisture. 5. The accidental impact that happens in a drop or fall.

    How To Tell If Your Furnace Control Board Is Bad Phyxter Home Services

    95% new used Original for Daikin air conditioning board Frequency Board ...

    HVAC systems have many complex components to provide heat and cool air when needed. When your furnace malfunctions, locating the exact cause or knowing what to replace can be a challenge.

    It is advisable to call a professional HVAC repair service as the first step to avoid the risk of personal injury or damage to your system.

    That said, there are a number of diagnostic tools you can use to help point the HVAC technician in the right direction if you feel comfortable doing the following checks.

    Want to know what tools professional electricians use? Check out the following article: The Electrical Tools Every New Electrician Should Have in 2022

    Although the problem could originate in your electrical system, not your furnace, check your HVAC system first for irregularities.

    The most common causes of furnace malfunction to take note of include:

    Loose wiring

    Furnaces are prone to a bit of shaking and rattling during operation. Occasionally inner wires come loose to the point that they cause the unit to short circuit. Scheduling regular maintenance with a professional HVAC technician mitigates this issue.

    Clogged air filter

    HVAC filters accumulate dust and debris over time, compromising heat levels and indoor air quality. The buildup of dirt and dust clog the filter and cause the blower motor to overheat and run the risk of catching fire.

    Dirty Fuse

    Once diagnosed, a capacitator is a simple, inexpensive fix.

    Blower motor issues

    Can A Circuit Board Be Replaced

    A broken circuit board may be repaired or changed, and if youve seen it, you shouldnt be concerned. Repairing a circuit board is a time taking process and requires proper inspection. However, replacing the circuit board all together can save you from the burden of replacing it later. It is preferable to replace a circuit board since older circuit boards have small and weak contact points, resulting in the most faults.

    What Causes An Acs Pcb To Become Damaged

    PCB circuits are highly sensitive to electrostatic discharge and various elements. It is very important to be aware that even small ESD discharges can damage the PCBs components. The following are some of the most common reasons why AC PCBs become damaged.

    • Improper input voltage in the ACs PCB while a technician is installing it.
    • Short circuit This is the most common cause by far of PCB damage.
    • Cockroaches, ants, and other small insects are widely known that cockroaches and other insects like warm places. Therefore, they often hide in electronic and electrical devices that produce heat. That is why whenever a cockroach gets inside the circuit board, it will most likely cause damage via short circuits, create static charges, and other problems.
    • Exposure to various elements. Dust, moisture, and heat exposure are common causes of PCB damage.
    • Accidental impact That involves accidents such as dropping it during the cleaning process.
    • Another common factor is age Everything in the world has an age limit. Most PCB components, unfortunately, have limited age limits.

    Related Posts